Lorry Garage Repair Services - Clutches

Complete the Lorry Clutch enquiry form and we'll arrange cost estimates from independant local Lorry clutch fitting garages

Lorry Clutch Fitting

The clutch in your Lorry connects and disconnects the engine from the gearbox (transmission) allowing smooth gearchange and control of the Lorry engine power.

A clutch plate (driven plate) is coated on both sides with a hard wearing high friction material. This is situated between the engine flywheel and a spring loaded pressure plate. The spring/pressure can be released by depressing the clutch pedal.

While driving, the whole clutch assembly can be turning at very high speeds. To allow a non rotating clutch pedal to control the rotating clutch assembly a clutch release bearing uses a fork acting on a thrust face

Lorry Clutch - Controlling Engine Torque

The clutch has to transmit the engine power to the wheels allowing the vehicle to move. The torque of the engine is transferred by the Lorry clutch system relying entirely on the contact friction between 2 faces. A slipping clutch occurs when the friction is too low (often due to clutch wear) or engine torque is too high (during rapid acceleration)

Controlling Power Transmission via The Clutch - Clutch Slip

The torque capacity (how much power can be transmitted without slipping) depends upon:

  • The Coefficient of Friction of the engaging Clutch Faces
  • Diameter of the Clutch Plate
  • The Pressure or Spring Loading

In order to use greater engine torque in high performance vehicles a multi-face clutch may be used compared to the single plate clutch system adopted on most Lorry cars.

How a Car Clutch Works with Normal Manual Driving

A car clutch is engaged/disengaged using the left most "clutch" pedal.
The clutch pedal is depressed to disengage the engine from the gearbox and drive train while changing gears. Once the gear is selected, the clutch pedal is released and the engine is once-again linked via the drive train
The clutch operation can be actuated by:

  • A Mechanical Linkage
    The clutch pedal is connected directly to the clutch assembly via a mechanical linkage such as cable or chain.
  • A Hydraulic Clutch
    Depressing the clutch pedal increases pressure in a hydraulic piston coupled to the clutch pedal. The increased pressure is transferred to a secondary piston that operates a lever to engage-disengage the clutch plates
  • An electronic clutch - Clutch by Wire
    Sensors detect the position of the clutch pedal electronically and interpret the position using an Electronic Control Unit (ECU) that computes the best way to operate the clutch based upon information relayed from other sensors indicating driving speed, engine speed and so on. The ECU relays information to a servo unit to actuate clutch operation.

Lorry Clutch Servicing, Lorry Kit Fitting & Lorry Repairs

Lorry Clutch service for North East England

Clutch

New Lorry clutches fitted to most Lorry makes using the Lorry recommended clutch kits

Lorry Garage Services

  • Use the simple enquiry form to request a repair estimate for the following types of Lorry garage services
  • Lorry Alternators
  • Lorry Body Repairs
  • Lorry Brake Servicing
  • Lorry Cooling Systems
  • Lorry Gearbox
  • Lorry Exhaust Systems
  • Lorry Fuel Injectors
  • Lorry Pollen Filters
  • Lorry Head Gasket
  • Lorry Starter Motors
  • Lorry Timing Belts
  • Lorry Suspension - Springs
  • Lorry PCV Valve Replacement

Lorry Faults

  • Lorry OBD
  • Lorry Fault Codes
  • Lorry Service Reset

Lorry Clutch Services

  • Clutch
  • Lorry Clutch Kit
  • Lorry Clutch Repairs
  • Lorry Clutch Master Cylinder
  • Lorry Clutch Slave Cylinder
  • Lorry : Specialist Repairs